Simplex 4004 Instruction Manual download pdf (Page 1)

4004 Fire Alarm

City Connect Card and DACT Module

Installation Instructions

 1999 Simplex Time Recorder Co., Gardner, MA 01441-0001 USA

All specifications and other information shown were current as of publication, and are subject to change without notice.

574-077

Rev. B

DO NOT INSTALL ANY SIMPLEX PRODUCT THAT APPEARS

DAMAGED. Upon unpacking your Simplex product, inspect the contents of

the carton for shipping damage. If damage is apparent, immediately file a claim

with the carrier and notify Simplex.

ELECTRICAL HAZARD - Disconnect electrical power when making any

internal adjustments or repairs. Servicing should be performed by qualified

Simplex Representatives.

STATIC HAZARD - Static electricity can damage components. Therefore,

handle as follows:

1. Ground yourself before opening or installing components (use the 553-484

Static Control Kit).

2. Keep uninstalled components wrapped in anti-static material at all times.

RADIO FREQUENCY ENERGY - This equipment generates, uses, and can

radiate radio frequency energy and if not installed and used in accordance with

the instruction manual, may cause interference to radio communications. It has

been tested and found to comply with the limits for a Class A computing device

pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide

reasonable protection against such interference when operated in a commercial

environment. Operation of this equipment in a residential area may cause

interference in which case the user at his own expense will be required to take

whatever measures may be required to correct the interference.

The 4004 Fire Alarm System is capable of supporting either one City Connect

Card (565-577, 565-999, or 566-078) or one DACT module. This publication

covers the procedure for installing a city connect card into a 4004 Panel. It also

covers the procedure for re-installing a 2080-9044 DACT into a 4004 Panel for

existing jobs.

For new DACT installations use the 4004-9810 DACT (565-626). Refer to the

Contact Closure DACT (Digital Alarm Communication Transmitter) Installation

Programming Instructions (574-049) for more information on the 4004-9810

DACT.

The following topics are covered in this publication:

Topic See Page #

Overview 1

City Connect Card Installation 2

DACT Module Installation 4

Cautions and Warnings

Overview

In This Publication

Technical Manuals Online! - http://www.tech-man.com

1 2 3 4 5 6

Summary of Contents

Page 1 - Installation Instructions

4004 Fire AlarmCity Connect Card and DACT Module Installation Instructions 1999 Simplex Time Recorder Co., Gardner, MA 01441-0001 USAAll specificatio

Page 2

2For all wiring information, use the 4004 Field Wiring Diagram (841-992). Alsoreference the Contractor Wiring Termination Label (519-698) inside the

Page 3 - Continued

3The city connect card has jumper settings that select either the Remote Station(Reverse Polarity) Interface (see Table 1), which is the default jumpe

Page 4 - DACT Module Installation

4Note: The following installation procedures are for the Silent KnightModel 5128 only.CAUTION: Disconnect power for the 4004 Panel at the breakerbefor

Page 5

57. Cut and strip the green Earth connect wire on the DACT module andconnect to the 4004 Back Box using an 18 AWG green wire and wire nut.Isolate the

Page 6

574-077Rev. B9. Connect Wiring Harness (733-897, supplied) from System Board P5 toDACT module P2, P5, and TB1.10. Power-up and configure the 4004 Sy

Simplex 4004 Instruction Manual Page 1

Browse online or download Instruction Manual for Smoke detectors Simplex 4004. Simplex 4004 Instruction manual User Manual

Summary of Contents

More documents for Smoke detectors Simplex 4004

Comments to this Manuals