Simplex 4100ES-S1 User Manual Page 16
- Page / 118
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
4100ES-S1 Programming Guide Document: LT0400
About the Programming Tools
3-2
3.1 General
The 4100ES-S1 Panel can be programmed by downloading into it a configuration file that
meets the desired site installation requirements.
3.2 ES Programmer
The programmer for the 4100ES-S1 panel is a Windows based application with graphical
interface that enables the user to build a specific site configuration (job) and download the
configuration image into the 4100ES-S1 panel via the PC Ethernet connection.
The programmer operation is controlled by a Programming Key (Dongle) that must be
attached to either the PC parallel port or USB socket (depending on the dongle type) to
enable programming access. USB dongles take up to 1 minute to be recognized by the
software, so don’t expect it to be immediately ready when first plugged in.
It is essential to use the ES Programmer version that matches the Panel Master Exec
version. The following table summarises the compatibility of the ES Programmer versions
with the 4100ES-S1 Panel Exec versions.
Panel Exec Version
Programmer Version
Programmer Part Number
1.02.04
1.02.02
SF0458
The appropriate programmer can be ordered using the part number listed.
3.3 4100ES-S1 Configuration Templates
The 4100ES-S1 panel is shipped with a basic 16 zone configuration to meet the Australian
standard. The configuration templates (part number SF0459) can be used by installation
technicians as the basis for each new 4100ES-S1 site-specific configuration.
3.4 ES Programmer Installation and Launch
Log on to the computer as an administrator and then run the ES Programmer installation
executable and follow the instructions – this will install the new programmer and other ES
programming utilities on your PC. There is no need to uninstall any old versions as multiple
versions can co-exist simultaneously. In fact it can sometimes be useful to have different
versions of the programmer installed to support the different Panel Exec versions in the field.
The installation process will create a directory named after the Programmer’s version (e.g.,
ES Ver 1.02.02) under the ‘C:\Program Files\Simplex\ES Programmer’ directory.
To launch the programmer click Start | (ALL) Programs | Simplex | the appropriate version
number | ES Programmer.
- Programming Guide 1
- AMENDMENT LOG 3
- TABLE OF CONTENTS 4
- 1 Introduction 7
- 1.1 About this Manual 8
- 1.2 Before you start 9
- 2 System Overview 11
- 2.1 General Description 12
- 2.2 Programming 13
- 3.1 General 16
- 3.2 ES Programmer 16
- 4 Creating a Configuration 19
- 4.4 Adding the AZF Logic 21
- 4.5 Where to Next? 21
- Adding Addressable Devices 25
- 6.1 Introduction 32
- 6.3.1 4099-9032 MCP 33
- 6.3.3 4090-9002 Relay IAM 34
- 6.3.4 4090-9007 Signal ZAM 34
- 6.3.5 4090-9101 Monitor ZAM 34
- Addressable Device Settings 35
- 7 Adding Zone Displays 39
- 7.1 General 40
- 8 Adding Expansion Modules 47
- 8.1 General 48
- Adding Expansion Modules 50
- 9 Custom Control 61
- 9.1 General 62
- 9.2 Custom Control Syntax 62
- 9.3 Creating a New Equation 64
- 9.3.2 Add Input Statements 65
- 9.3.3 Add Output Statements 66
- 10 AS1668 Fan Controls 69
- 4100ES-S1 70
- AS1668 Fan Manual Start: 71
- 10.4.1 Switch Configuration 74
- 10.4.2 LED Configuration 75
- 10.4.3 Point Editing 76
- 10.5.2 Set up Register 8 78
- 10.5.3 S/A DETECTOR Isolate 78
- 10.5.5 S/A DETECTOR ACTIVE 79
- 10.5.6 Trigger FAN ON 79
- 10.5.7 Trigger FAN OFF 79
- 10.5.8 FAN Fault Conditions 80
- Configuration 81
- 11.1 Building the Job 82
- 11.2.1 IP File Transfer 83
- 11.2.2 Connection to the PC 83
- 11.5 IP File Transfer 84
- 11.5.3 Upload/Reports Tab 86
- 11.5.4 Mass Storage Tab 88
- 11.5.5 History/Undo Tab 89
- 12 Appendices 95
- 12.2.2 Analog Points 98
- 12.2.3 Lists 98
- 12.2.5 Battery Test 99
- 3-3 ASE Fault Relay 101
- 2x 40 CHARACTER 102
- LCD DISPLAY 102
- 5-1 ZONE 1 Alarm Test 106
- 5-2 ZONE 1 Fault Test 106
- 3-17 A/C Trip Reset 106
- References 107
- 12.3.7 Clean up Equations 108
- Reset zone isolate toggle 109
- 12.4.1 Digital Points used 110
- 12.4.5 Zone n Equations 112
- ZONE n Isolate 113
- ZONE n Alarm LED Off 113
- Mapping 114
- System Digital Pseudo Points 116
- System Lists 117
- System Analog Pseudo Points 117
Related products and manuals for Fire protection Simplex 4100ES-S1
(86 pages)© 2020, manymanuals.com. All rights reserved. | 0.251 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals